Home›Industries›Specialty
Industries We Serve
ESD-rated flooring, parking deck waterproofing, contamination-controlled environments, and the specialty installations where the wrong system isn’t just a wear problem — it’s an operational, compliance, or safety problem. Most facility managers don’t know what to spec. Our job during the site survey is to figure that out for you.
Most buyers searching for specialty commercial flooring know they have a problem — they just don’t know what to ask for. If any of the following sound like your facility, this page is written for you:
“We’ve had unexplained equipment failures, lost circuit boards, or inventory that fails QC and we can’t pinpoint why.”
You may need ESD (electrostatic-dissipative) flooring. Static buildup in electronics manufacturing, avionics, server rooms, and component repair facilities causes failures that look random until the floor is identified as the culprit.
“Our parking deck has cracks, leaks dripping into the level below, or visible reinforcing steel.”
You need a parking deck waterproofing system — a traffic-bearing membrane that stops water infiltration, protects the structural concrete, and handles freeze-thaw cycling. Standard parking lot epoxy doesn’t solve this problem.
“Our facility has contamination control protocols and the floor is part of our compliance.”
You need a cleanroom-grade or contamination-controlled resinous floor — low-particle, easy to disinfect, with seamless integral cove bases. Pharmaceutical packaging, medical device assembly, food production cleanrooms, and electronics fabrication all share this requirement.
“Our gym or athletic facility has heavy weights damaging the floor, or we need impact-rated surfaces.”
You may need a specialty fitness flooring system with rubber overlays or impact-rated resin. We install these when specified, though they’re a smaller part of our work — we’ll be honest with you on the site survey about whether we’re the right fit or whether a fitness-specialty contractor would serve you better.
“The architect spec says ‘ESD,’ ‘cleanroom,’ ‘ASTM,’ or another standard we don’t fully understand.”
Bring us the spec. We’ll walk through what it actually requires, whether the spec is right for your operation, and what the install really involves — in plain language.
Why Specialty Work Fails When Handed to Generalists
A standard commercial epoxy looks similar to an ESD-rated system. They both end up smooth, hard, and resin-based. The difference is what they do. An ESD floor is engineered to dissipate static charge to ground at a tested resistance range. If it’s installed without conductive grounding strips and without testing, it looks identical to a non-ESD floor — and the equipment failures it was supposed to prevent will continue.
Same logic applies across the specialty categories. A parking deck waterproofing system without the proper membrane installation will leak through to the level below — even if the topcoat looks perfect. A “cleanroom” floor installed without low-particle materials and integral coving will fail the contamination control audit. The wrong system isn’t a wear problem in five years. It’s a failure to solve the problem from day one.
This is why specialty work demands a contractor who understands what the system is engineered to do — not just one who can install resin on concrete.
The Three Primary Specialty Categories We Install
If you’re a facility manager who’s never spec’d a specialty floor, the technical names sound similar and the specifications read like another language. Here’s what each system actually does, when it’s the right answer, and what to expect during installation.
Category 01
Electronics manufacturing · Avionics · Component repair · Server rooms · Munitions handling
What problem it solves
In environments where static electricity damages sensitive electronics or creates ignition risk, the floor itself becomes part of the static control system. An ESD-rated floor dissipates static charge to ground through a network of conductive copper grounding strips beneath the resin surface, holding floor resistance within a tested range that prevents both static buildup and dangerous direct conductivity.
What we install
Conductive epoxy and static-dissipative resinous systems specified to IEC 61340-5-1 and ANSI/ESD STM standards, with measured surface and surface-to-ground resistance typically in the 10⁶ to 10⁹ ohm range depending on the application. We install copper grounding networks, ESD-rated primer systems, conductive base coats, and topcoat formulations chosen for the specific operation.
An honest note
ESD flooring only works when the rest of your static control program works — ESD wrist straps, properly grounded benches, and trained operators. We can install the best ESD floor in the country and your equipment will still fail if the rest of the system isn’t in place. We’ll talk through the whole picture during the site survey.
Category 02
Multi-level parking structures · Plaza decks · Mechanical level decks · Garage tops
What problem it solves
A parking deck looks like a slab of concrete you drive on. It’s actually a structural element subject to traffic loading, freeze-thaw cycling, salt-laden runoff, and concrete deflection. Without a waterproofing system, water penetrates the concrete, attacks the reinforcing steel, and accelerates structural deterioration — often visible as rust stains, spalling, or active dripping into the level below.
What we install
Traffic-bearing waterproofing membranes — typically a multi-coat system with a flexible base coat that handles concrete deflection, an intermediate aggregate-broadcast layer for traction, and a UV-stable wear topcoat. The system bonds chemically to the concrete and remains flexible to handle thermal movement and structural deflection without cracking.
An honest note on scope
Parking deck waterproofing is not the same as putting epoxy on a parking lot. If your problem is a flat surface lot with cracking concrete, you don’t need a waterproofing system. If your problem is structural water infiltration through an elevated deck, generic concrete sealer won’t fix it. Part of our job is helping you understand which one you actually have.
Category 03
Pharmaceutical packaging · Medical device assembly · Food production cleanrooms · Electronics fabrication
What problem it solves
In contamination-sensitive operations, the floor is part of the contamination control system. It must be seamless (no joints to harbor particles), low-particle (the floor itself can’t shed contamination), easy to disinfect (smooth, non-porous, chemically stable against the cleaning protocols actually used), and integrally coved (no floor-to-wall joint where contamination collects).
What we install
Seamless resinous flooring systems with integral cove bases, low-VOC and low-particle formulations, and topcoats specified for the disinfection chemistries the operation will actually use. Systems are installed with attention to the joints, transitions, and detail work that determine whether a contamination-control audit passes or fails.
When we’re a fit
If your facility has contamination control protocols and needs flooring that supports those protocols, we’re a strong fit. If you need a turnkey ISO-certified cleanroom build with full validation and certification, we’ll partner with cleanroom specialists who do that as their primary business and we’ll tell you up front during the site survey.
Other Specialty Capabilities
A few categories come up frequently enough to mention, but we want to be straight with you about how we approach them: we install when the project specifies them, but we’re not positioning as specialists in either category.
Specialty Fitness Flooring
When a fitness facility project comes with a specification calling for impact-rated resin systems or rubber-overlay assemblies, we install them. The work is real and we do it correctly.
If you’re building a high-end performance training facility where the floor is the central piece of the build, a fitness-specialty contractor may serve you better. We’ll be honest about that on the site survey rather than saying yes to win the job.
Sloped-to-Drain Installations
Most sloped-to-drain work is part of broader industry installations — commercial kitchens, locker rooms, vet facilities, food processing plants. The slope is designed by the architect or plumber; we install the resinous floor system over the sloped concrete and detail the drain transitions correctly.
If you’re searching for “sloped-to-drain flooring” specifically, you’re probably looking at one of our Food & Beverage or Commercial & Institutional applications — those pages cover the operational realities in detail.
How an Education-Driven Buyer Engages With Us
If you’re a facility manager who knows you have a problem but doesn’t know what to ask for, here’s how the conversation typically goes:
Step 01
Describe the symptoms in plain language. Equipment failures. Visible leaks. Audit findings. Whatever the operational problem is. We’ll tell you whether flooring is part of the answer or whether you actually have a different problem.
Step 02
Michael or Colby visits in person, sees the conditions, asks about your operations and constraints, and identifies the specific specialty system the situation actually needs.
Step 03
You get a recommendation in language a facility manager can use — not a specification document. If the project needs to be formally specified before you can budget for it, we’ll help you produce that document or work with your architect to do so.
How We Approach Specialty Work
Specialty floors demand a contractor who understands the engineering behind the system, not just one who can install resin on concrete. That’s what our diagnostic process is built for.
Read about our diagnostic-first processTell Us What You’re Trying to Solve
Schedule a site survey. Describe what’s happening at your facility — the symptoms, the constraints, the questions you don’t know how to ask. We’ll walk the space, identify what specialty system the situation actually needs, and give you a recommendation in plain language. Forty-five minutes of an owner’s time, no obligation.